KB Coatings — Built to Perform
Commercial & industrial specialty coatings · Serving facilities nationwide

Frequently asked questions

Answers to common questions about the coating, repair, and surface preparation work KB Coatings does for commercial and industrial facilities.

What kind of coating work does KB Coatings do?

We specialize in coatings that improve wear resistance, restore performance, and extend the useful life of commercial and industrial facilities and equipment. That includes epoxy floor systems, concrete repair, trench and containment repair, protective coatings for industrial structures such as silos, and restoration coatings for worn equipment such as pump casings. Typical sites are production floors, warehouses, shops, service bays, maintenance areas, and industrial plants. KB Coatings does not do residential work.

What coating systems do you install, and how do you choose one?

We install epoxy floor systems and other specialty and protective coatings, including ceramic-filled epoxy for worn equipment. The choice starts with the conditions, not a standard product: what the surface is made of and what shape it is in, the traffic it sees, any chemical, water, or heat exposure, and how soon the area has to go back into service. The system is matched to that environment, so the surface holds up to wear and lasts longer in service, instead of using one system everywhere.

What causes floor coatings to fail?

Most failures start underneath the coating. Common causes are poor surface preparation, moisture coming up through the concrete, cracks or damaged concrete that were coated over instead of repaired, and a system that was not suited to the traffic or chemicals in that area. That is why we look at the substrate, the wear pattern, and the work conditions before recommending anything.

How is the surface prepared before coating?

Preparation gets as much attention as the coating itself. On concrete, that means grinding or shot-blasting to the right profile, as the job requires, then repairing cracks and spalls, patching rough sections, and cleaning the area so the coating can bond. On metal, it means getting down to sound metal and reinforcing weak areas such as seams before the coating goes on.

Do you test concrete for moisture?

Yes, on every concrete job. Moisture in concrete is a common reason floor coatings fail, so it is tested before a coating system is chosen and installed. If moisture is a concern, that affects which system is recommended and what preparation is needed before anything goes down.

What can be done with cracked or spalled concrete?

In many cases it can be repaired instead of replaced. Cracks are opened up and filled, spalled and rough sections are patched, and damaged areas are brought back to a sound, level surface before a coating system goes down or the area is turned back over. Repairing the concrete first matters: coating over damaged concrete usually just hides the problem for a while.

Can an old coating be coated over, or does it have to come off?

It depends on the existing coating. If it is still well bonded and compatible with the new system, it may be possible to prepare it and coat over it. If it is peeling, blistering, or has failed, it needs to come off so the new system bonds to a sound surface. We check the existing coating's condition on site before recommending either approach.

How do you handle areas exposed to acid or chemicals?

The coating system has to be chosen for the specific exposure, and the surface underneath has to be sound. At Liberty Steel, the containment area around acid storage tanks had failed. KB Coatings repaired the containment area, the trench, and adjacent floor sections, and the job grew to roughly 3,000 sq ft of resurfacing, all in an active industrial work area. The area was turned over ready for service.

How do you coat trenches, sumps, and secondary containment?

These areas take standing liquid, chemicals, and cleanup, so failures there have real operational consequences. The work usually starts with removing failed coating and repairing damaged concrete, including edges and joints where problems tend to start. The surface is then prepared and coated with a system suited to what the area holds. Trench and containment work is a core part of what KB Coatings does.

Do you coat industrial structures like silos?

Yes. When spot repairs on an industrial structure keep failing, a full repair and coating is often the longer-lasting fix. At Merom Station, a fly ash silo had ongoing leaks that kept creating maintenance issues. KB Coatings prepared the surface down to sound metal, reinforced the seams, and applied a seamless protective coating built for longer service life. The leaks were stopped, and the silo went back into service with better long-term protection.

What is pump casing or equipment restoration?

It means rebuilding worn equipment surfaces with a coating instead of replacing the part. At Hallador Power, six scrubber pump casings had severe wear and pitting. KB Coatings rebuilt the worn surfaces with a ceramic-bead-filled epoxy layer to restore efficiency, add wear resistance, and extend service life. The casings went back into service without the cost and delay of replacement.

Can you work around operations, nights, weekends, or shutdowns?

Yes, when the job requires it. We can work nights, weekends, or during shutdowns, and work can often be done while the rest of the facility keeps running, as it was at Liberty Steel. Before work starts, we go over access, sequencing, and which areas have to stay open, so the job can be planned in sections if needed.

To get a quote, send the location, the area and its rough size, what it is exposed to, and a few photos to info@kb-coatings.com, or call (314) 499-1113.

Service area

Based in the St. Louis region. Working nationwide.

KB Coatings is based in Waterloo, Illinois, in the St. Louis region, and works nationwide on coatings that improve wear resistance, restore performance, and extend the useful life of commercial and industrial facilities and equipment.

Close to home, that includes the St. Louis metro, the Metro East, Southern Illinois, and Missouri. Outside the region, we take on industrial floor and containment repair, surface preparation and concrete repair, protective coatings, and equipment and industrial structure restoration. Recent work has included a fly ash silo at a power station, power plant pump casings, and acid containment repair at a steel facility.

Every job, local or not, starts the same way: we look at the actual surface condition, the environment it is exposed to, and how the area has to operate during the work. Then we match the repair and coating approach to those conditions.

Wherever your facility is, send the location, scope, and a few photos, and we'd be happy to discuss your job.

Call (314) 499-1113 or email info@kb-coatings.com.

Next step

Have a coating, repair, or surface problem to talk through?

Send the location, the area, and a few photos, and KB Coatings can look at the scope and the existing condition.